跳至主要内容

Why is the stainless steel centrifugal water pump very quiet?

Most of the time when a electric pump started, it makes a buzzing sound,the normal cast iron water pump 's sound is about 40db.
If the water pump works ,it is affect our rest and sleep.so pump station usually build far away from resident house.some pump station even were designed and built under ground.
The sound of water pump runing has two prats,one is because the motor drive the pump,then there is sound made by electric motor.the other is come from the pump tunnerl,the impeller drives the water, the flow and impeller has friction,the sound comes out.
Gelaili GDL series water pump and HL series water pump are made of stainless steel,they are very quite,they run only 12db,only slightly larger than the leaves blown by the wind.
Why stainless steel water pump is so quiet?
Due to rough surfaces of cast iron water pump,greater friction with the flow was caused.But the stainless steel impeller and tunnel is very smooth,the friction is very small,so the stainless steel water pump is so quiet that you can not notice it is exist.
Besides,these pumps are all use NSK bearing,so when you operate the water pump,it is very low sound.
Gelaili stainless steel water pump,protect your sleep time,keep you away from noisy,leave you only peace and quiet every night.
Gelaili pump industry supply good pumps with 50 years manufacture experience.
We provide aquarium water pump,shower pump, coolant pump,dirty water pump,dewatering pumps,booster pump,ro booster pump and so on.

标签：

评论

发表评论

此博客中的热门博文

Causes of Electric Motor Burning by Water pump

1. First, find out whether the motor burns the bearing (mechanical fault) or the coil (electrical fault). If it is the fault of burning coil, it is mainly caused by overcurrent, sometimes too high or too low voltage will also cause the coil to heat and short circuit, so check that the voltage when running is too different from the rated voltage.There may be several reasons for over-current short-circuiting: A. the equipment is overloaded to make the motor run for a long time at rated or over rated current. In particular, the starting current of the motor is 3-5 times that of the rated current. Therefore, we should try to avoid running with load or full load when starting the equipment (mainly depending on the matching allowance of rated current and normal operating current of motor). B, the motor works in a wet working environment. The insulation of the coils should be checked before the motor starts. The insulation requirements of different voltage grades are also different. May r...
发表评论
阅读全文

The advantages of the stainless steel centrifugal pump

The stainless steel  centrifugal water pump  can be used to convey various medium from tap water to industrial liquid at different temperature with different flow and pressure.the stainless steel  centrifugal water pump  can be used to transport the liquid,which PH Value is 5-9,the liquid can be slightly alkaline water,take off a mineral water,distilled water,swimming pool water,chloride liquid, they are anti-corrosion pumps. Stainless steel  centrifugal water pump  can last for a long time, stainless steel gear pump because the high quality material and light weight rotating parts, the stainless steel  centrifugal water pump  life expectancy is much longer than the ordinary pump. Gelaili pump industry ,supply professional stainless steel water pump. www.jxgllpump.com
发表评论
阅读全文

Difference between suction stroke and lift head of water pump

Pump self-priming capacity is also called maximum self suction height.It is the maximum height at which the water is pumped (the vertical distance between the pump and the the liquid surface to be pumped) without fill in water into the pump tunnel. General water level is lower than the location of the pump, you need to pump self-priming capacity.For example ,if we need to pump water from a river ,we will not plan pipe first,so we need a pump which has self-priming capacity. Or we need to pump some corrosive liquid,we can not fill water into the water pump tunnel. Some centrifugal water pumps do not have self-priming capacity,they need to fill in water at first time of using. The pump lift is the height that pump can lift water up.We usually expressed in H,the the unit is meter. The lift of the centrifugal pump is based on the center line of the impeller.The lift Consists of two parts,first is the vertical height from the center line of the pump impeller to the surface of the water s...
发表评论
阅读全文