跳至主要内容

Frequency converter to centrifugal water pump

In the north of China, most water plants use the differenct size of pump to connect together and parallel water supply.In order to meet the requirements of different water supply indexes.the pump start and stop running frequently,to make use of different combinations pump way to meet the needs.Thus, the energy loss caused by the start and the aging of equipment caused by frequent starting will be unnecessary waste.Using frequency conversion speed regulation system to adjust water pump operation is a good way to solve this problem.
 Frequency water supply is automatically adjust the rotation speed of one pump or run/stop one or more pumps, which is the best water supply way to keep the water supply net to be stable,Product The frequency convention water supply has a lot of advantages:
 it providing constantly water supply regardless of power failure.
 Gelaili products are all stainless steel channel, health, no secondary pollution.
 the syetem is full automatic control operation, unattended design.
 Gelaili pup system’s water pressure is stable, won’t cause adjacent municipal pipe network pressure fluctuations.
 People can use frequency converter to control speed of the pump according to water consumption,energy saving.

标签：

评论

发表评论

此博客中的热门博文

Why Ro booster pump in a water treatment system does not work?

Why Ro booster pump does not work?Let's find out the reason. Reverse Osmosis booster Pump is one of the key part of the RO water purification machine,we call it ro booster pump,It is a kind of booster pump be used in the reverse osmosis device, it has the function of self-priming and pressurization. Ro booster pump provide Ro membrane water pressure and water flow,to make Ro rembrane work. Ro membrane is another important component of the RO water purification machine.So Ro water purification machine can give us purifield water. Some times ro booster pump does not work,so the whole system is out of work,there are follow reasons cause the ro booster pump doesn't work: 1,Purifield water tank at a high level or the original water tank is at a low position. 2,Ro water pressure is higher than the protection switch Settings, the controller automatically switched on. 3,Ro booster pump suction pressure is lower than protection switch Settings, the controller automatically discon...
发表评论
阅读全文

A centrifugal water pump show us your capability

In recent decades, China’s property market has entered a rising rapidly, the purchasing power exuberant state. However, due to the recent weakness in the market, the property market began to gradually slow down, into a stable, and even occasional decline stage. Recently, one of my friends suddenly called me and excitedly told me that he had taken a fancy to a house in the neighborhood,the real estate belongs to Poly property, it is said that the property just opened, it attracted many buyers of onlookers.in just a few days, the house has been sold out.My friend has been on the sidelines all the time, as he has a set of property, not anxious to buy second sets of houses,instead, he chose carefully and wanted to buy one sets around the good evironment,he wanted it is a quality and residential environment are both very good house.I don’t know why he has taken a fancy to this neighborhood recently. My friend was excited to invite me to go with him to purchase procedures,So, we came to t...
发表评论
阅读全文

Causes of Electric Motor Burning by Water pump

1. First, find out whether the motor burns the bearing (mechanical fault) or the coil (electrical fault). If it is the fault of burning coil, it is mainly caused by overcurrent, sometimes too high or too low voltage will also cause the coil to heat and short circuit, so check that the voltage when running is too different from the rated voltage.There may be several reasons for over-current short-circuiting: A. the equipment is overloaded to make the motor run for a long time at rated or over rated current. In particular, the starting current of the motor is 3-5 times that of the rated current. Therefore, we should try to avoid running with load or full load when starting the equipment (mainly depending on the matching allowance of rated current and normal operating current of motor). B, the motor works in a wet working environment. The insulation of the coils should be checked before the motor starts. The insulation requirements of different voltage grades are also different. May r...
发表评论
阅读全文