跳至主要内容

Floor heating is not warm, choose booster pump or circulating pump ?

Booster pump and circulating pump, as the name suggests, have different performance, in the installation position, scope of application, operation and control and so on have their own characteristics, with obvious difference.
1. working principle
Circulating pump: circulation refers to the role of the pump, centrifugal refers to the structure of the pump, the two are completely two concepts. The working principle of the circulating pump to water circulating pump is called a circulating pump, such as water heating pipe in the hot water is circulating by the circulating pump up
Booster pump: first liquid booster pump is full, and then start the fast rotating impeller, centrifugal pump, impeller blades driven by fluid rotation, the liquid is rotated by the inertia to flow to the outer edge of the impeller, the impeller from the suction chamber into the liquid at the same time, the force on the work of the liquid to liquid, and then the energy out of the impeller, the liquid the kinetic energy and pressure energy can be increased.
2. installation position
The booster pump is usually installed in the water pipe, the original pipeline cut after a period of pump series to the pipeline can; circulating pump should be installed in the return pipe, pressure boosting system, to help them with a circulation pipeline, scissors cut, pump series on the line.
3. scope of application
The booster pump is generally used in central heating systems, solar and led to less drop of water pressure is small, and the water heater pressure small, need pressurized condition; circulating pump is mainly for self heating users, or in the large-sized apartment home heating system circulation, heating hot water circulation use. If the water temperature, water temperature is low. Install the circulating pump can solve the problem, but if the return water temperature is low, you need to first find the reasons not hot.
4. supercharging strength
Booster pump mainly solves the problem of small water pressure, belongs to the type of pressure smaller pump, which is determined by the structure of the pump, the booster pump is pressurized by centrifugal force; and the circulation pump compared to the booster pump pressure, can drive the entire heating system cycle
5. product operation
The booster pump is mostly automatic control, that is, the switch is the automatic switch control of water flow. As long as the water flow switch starts automatically, there is no automatic shutdown of water flow. Most of the circulating pumps are manually controlled, and people need to switch on manually, so as to achieve the connection and operation of pumps.
The booster pump and circulating pump exist many differences, so in the purchase and use of the process, the user must pay attention to identify and distinguish the two types of pumps used, well, otherwise it will be difficult to meet their own needs, and even damage the whole system. You are not sure when to buy what kind of water pump and try to consult professionals, listen to their purchase recommendations.
Gelaili is a mainly professional manufacturer of electric pump,fire pump,coolant pump,dewatering pumps,booster pump,ro booster pump and so on.
We provide all kinds of good coolant pump,dirty water pump,shower pump,dewatering pumps,booster pump,ro booster pump.
more you can see from：www.jxgllpump.com
标签：

评论

发表评论

此博客中的热门博文

Causes of Electric Motor Burning by Water pump

1. First, find out whether the motor burns the bearing (mechanical fault) or the coil (electrical fault). If it is the fault of burning coil, it is mainly caused by overcurrent, sometimes too high or too low voltage will also cause the coil to heat and short circuit, so check that the voltage when running is too different from the rated voltage.There may be several reasons for over-current short-circuiting: A. the equipment is overloaded to make the motor run for a long time at rated or over rated current. In particular, the starting current of the motor is 3-5 times that of the rated current. Therefore, we should try to avoid running with load or full load when starting the equipment (mainly depending on the matching allowance of rated current and normal operating current of motor). B, the motor works in a wet working environment. The insulation of the coils should be checked before the motor starts. The insulation requirements of different voltage grades are also different. May r...
发表评论
阅读全文

The advantages of the stainless steel centrifugal pump

The stainless steel  centrifugal water pump  can be used to convey various medium from tap water to industrial liquid at different temperature with different flow and pressure.the stainless steel  centrifugal water pump  can be used to transport the liquid,which PH Value is 5-9,the liquid can be slightly alkaline water,take off a mineral water,distilled water,swimming pool water,chloride liquid, they are anti-corrosion pumps. Stainless steel  centrifugal water pump  can last for a long time, stainless steel gear pump because the high quality material and light weight rotating parts, the stainless steel  centrifugal water pump  life expectancy is much longer than the ordinary pump. Gelaili pump industry ,supply professional stainless steel water pump. www.jxgllpump.com
发表评论
阅读全文

Difference between suction stroke and lift head of water pump

Pump self-priming capacity is also called maximum self suction height.It is the maximum height at which the water is pumped (the vertical distance between the pump and the the liquid surface to be pumped) without fill in water into the pump tunnel. General water level is lower than the location of the pump, you need to pump self-priming capacity.For example ,if we need to pump water from a river ,we will not plan pipe first,so we need a pump which has self-priming capacity. Or we need to pump some corrosive liquid,we can not fill water into the water pump tunnel. Some centrifugal water pumps do not have self-priming capacity,they need to fill in water at first time of using. The pump lift is the height that pump can lift water up.We usually expressed in H,the the unit is meter. The lift of the centrifugal pump is based on the center line of the impeller.The lift Consists of two parts,first is the vertical height from the center line of the pump impeller to the surface of the water s...
发表评论
阅读全文