跳至主要内容

Application of pumps

Pump is a device that raises, transfers, delivers, or compresses fluid.It usually raise liquid from low position and transfer liquid to highier position,most of pumps are electric pump.
Pumps can used in agriculture:irragation;running water project:water raise,water transfer,water distribution,water pressure booster;waste water treatment:dirty water pump,drain water,transfer water,water filtration,like ro booster pump;Heat power station:boiler feedwater,coolant water,recycled water,clean ash;Mine and steelworks:drain water,hydraulic coal mining,Steel dephosphorization;oil industry:drilling project,oil transfer,water supply,oil suction,oil refining;chemical industry:chemical liquid,heat liquid,cool liquid.metal smelting;shipping industry:boiler feedwater,raise coolant water,tranfer recycled water,oil goods,clean ship cabin,balance the water go by ship, push ship forward;construction industry:drain water,dredging,concretion,shower pump;
building equipment:boiler feedwater,building water supply,drain waste water,temperature water cycle,aquarium water pump,air conditioning;light industry: pulp transfer,medicament transfer,ceramic slurry transfer;Food industry:drink,milk and so on transfer.

标签：

评论

发表评论

此博客中的热门博文

Why Ro booster pump in a water treatment system does not work?

Why Ro booster pump does not work?Let's find out the reason. Reverse Osmosis booster Pump is one of the key part of the RO water purification machine,we call it ro booster pump,It is a kind of booster pump be used in the reverse osmosis device, it has the function of self-priming and pressurization. Ro booster pump provide Ro membrane water pressure and water flow,to make Ro rembrane work. Ro membrane is another important component of the RO water purification machine.So Ro water purification machine can give us purifield water. Some times ro booster pump does not work,so the whole system is out of work,there are follow reasons cause the ro booster pump doesn't work: 1,Purifield water tank at a high level or the original water tank is at a low position. 2,Ro water pressure is higher than the protection switch Settings, the controller automatically switched on. 3,Ro booster pump suction pressure is lower than protection switch Settings, the controller automatically discon...
发表评论
阅读全文

A centrifugal water pump show us your capability

In recent decades, China’s property market has entered a rising rapidly, the purchasing power exuberant state. However, due to the recent weakness in the market, the property market began to gradually slow down, into a stable, and even occasional decline stage. Recently, one of my friends suddenly called me and excitedly told me that he had taken a fancy to a house in the neighborhood,the real estate belongs to Poly property, it is said that the property just opened, it attracted many buyers of onlookers.in just a few days, the house has been sold out.My friend has been on the sidelines all the time, as he has a set of property, not anxious to buy second sets of houses,instead, he chose carefully and wanted to buy one sets around the good evironment,he wanted it is a quality and residential environment are both very good house.I don’t know why he has taken a fancy to this neighborhood recently. My friend was excited to invite me to go with him to purchase procedures,So, we came to t...
发表评论
阅读全文

Causes of Electric Motor Burning by Water pump

1. First, find out whether the motor burns the bearing (mechanical fault) or the coil (electrical fault). If it is the fault of burning coil, it is mainly caused by overcurrent, sometimes too high or too low voltage will also cause the coil to heat and short circuit, so check that the voltage when running is too different from the rated voltage.There may be several reasons for over-current short-circuiting: A. the equipment is overloaded to make the motor run for a long time at rated or over rated current. In particular, the starting current of the motor is 3-5 times that of the rated current. Therefore, we should try to avoid running with load or full load when starting the equipment (mainly depending on the matching allowance of rated current and normal operating current of motor). B, the motor works in a wet working environment. The insulation of the coils should be checked before the motor starts. The insulation requirements of different voltage grades are also different. May r...
发表评论
阅读全文