跳至主要内容

How to increase the self-priming capacity of the centrifugal water pump

First method(simplest one)
Self-priming sewage pump vacuum pump is arranged in the water pipeline, water pump start before the vacuum pump starts to pump water pipe Neixianbu
with water, to ensure that the water pump, quick start.
This type of water absorption requires a perfect automatic control system to ensure normal work.
Second method(more simple)
The self – priming pump reduces the water inlet pipe curve , the fall height and the horizontal interval.
Third way( Trouble, but it works.)
The self-priming pump is equipped with a water suction tank in front of the pump. In this way, a suction tank should be installed on the pump suction
pipe. Before the first operation of the pump, the tank should be filled with water manually, and after the first operation the tank should be
stopped. Since the intake pipe of the suction tank is higher than the water level inside the pipe,the water in the tank will not flow back into the
pool, so the water can be stored in the tank, and because the water suction tank outlet pipe (that is, the suction pipe of the pump) is lower than
the water level inside the pipe. Therefore, it can ensure that the water absorption pipe of the pump is covered with water, and when the pump is
running again, the water in the water tank is pumped away by the pump, and the water in the pool is added to the water absorption tank under the
action of atmospheric pressure. Enter the pump through the pipes in the tank tank.
The fourth way
Self-priming sewage pump suction pipe. The suction end of the valve is installed at the end of suction end of the valve is actually a check valve, it
can only guarantee the flow by the pool into the suction tube can not turn the clock back, so if the water pipe is full of water, despite the
elevation axis pump the water level above the pool, but because there is the role of the water suction end of the valve. The tube into the pool water
will not enable the suction tube has been filled with water to ensure the pump can automatically, quickly start.
The fifth way
In the pump structure , for example , the self – priming pump in the figure below directly combines the vacuum impeller with the centrifugal pump .

Jiangxi Gelaili pump industry co.,ltd produce centrifugal water pump,we have CDL,CDLF series,CHL,CHLF series stainless steel electric pump,can be used as ro booster pump, shower pump,fire pump,coolant pump,aquarium water pump and so on,we also supply cast iron pump,they are WQ series dewatering pumps,dirty water pump and GD series pipeline pump.
Gelaili pump industry co.,ltd supplies you competitive price and high quality products. 

标签：

评论

发表评论

此博客中的热门博文

Pressure fluctuation propagation of a pump turbine at pump mode under low head condition

Pressure fluctuation at the vaneless space and vanes passages is one of the most important problems for the stable operation of a pump turbine. The fluctuation appears in any operating condition. Much research has been done on the pressure fluctuation of hydraulic machinery. However, the details of pressure fluctuation propagation of the pump turbine at the pump mode have not been revealed. The modern pump turbine with high water head requires the runner to be “flat”, which would induce pressure fluctuation more easily than the low head pump turbine. In this article, a high head pump turbine model is used as the research object. As the pressure fluctuation at off-design point is more serious than at the design point, the low head condition is chosen as the research condition. Pressure fluctuation at the vaneless space and vanes passages is predicted by the computational fluid dynamics method based on k- shear stress transport model. The experiment conducted on the test rig of the Har...
发表评论
阅读全文

Causes of Electric Motor Burning by Water pump

1. First, find out whether the motor burns the bearing (mechanical fault) or the coil (electrical fault). If it is the fault of burning coil, it is mainly caused by overcurrent, sometimes too high or too low voltage will also cause the coil to heat and short circuit, so check that the voltage when running is too different from the rated voltage.There may be several reasons for over-current short-circuiting: A. the equipment is overloaded to make the motor run for a long time at rated or over rated current. In particular, the starting current of the motor is 3-5 times that of the rated current. Therefore, we should try to avoid running with load or full load when starting the equipment (mainly depending on the matching allowance of rated current and normal operating current of motor). B, the motor works in a wet working environment. The insulation of the coils should be checked before the motor starts. The insulation requirements of different voltage grades are also different. May r...
发表评论
阅读全文

The advantages of the stainless steel centrifugal pump

The stainless steel  centrifugal water pump  can be used to convey various medium from tap water to industrial liquid at different temperature with different flow and pressure.the stainless steel  centrifugal water pump  can be used to transport the liquid,which PH Value is 5-9,the liquid can be slightly alkaline water,take off a mineral water,distilled water,swimming pool water,chloride liquid, they are anti-corrosion pumps. Stainless steel  centrifugal water pump  can last for a long time, stainless steel gear pump because the high quality material and light weight rotating parts, the stainless steel  centrifugal water pump  life expectancy is much longer than the ordinary pump. Gelaili pump industry ,supply professional stainless steel water pump. www.jxgllpump.com
发表评论
阅读全文