跳至主要内容

Characteristics and working principle of water treatment booster pump

Characteristics of water treatment booster pump
A booster pump uses a low-pressure gas (2-8 bar) of a wide area piston to produce high pressure gas / liquid on a small area piston.The booster pump can be used for compressed air and other gases, and the output air pressure can be regulated without pressure,The gas pipeline booster pump has single acting pump and double acting pump.The double acting pump piston compresses the gas in the two strokes of the reciprocating stroke,when the driving gas acts on the gas piston, the working piston can obtain larger output with the gas driving.

The booster pump has the following characteristics

1. The maintenance of the booster pump is simple, the parts and seals of the booster pump are less, the maintenance is simple, and the cost is low.

2, booster pump cost-effective: booster pump with high output performance and low cost characteristics

3, booster pump adjustable, pump output pressure and flow control valve by the pressure of driving gas accurately. Adjusting the driving pressure, the output pressure booster pump pressure pipeline accurately between the pre pressure and maximum output pressure adjustment.
4, booster pump output pressure high: pneumatic liquid pipeline booster pump maximum working pressure can reach 700Mpa, pneumatic gas pipeline booster pump maximum working pressure can reach 300Mpa.
5, booster pump material is fine, high pressure pump parts are divided into hard aluminum alloy, high pressure plunger material is stainless steel. And double layer seal. Key parts of material can be selected according to medium performance.

6, A variety of gas booster pump driven: the compressed air, nitrogen, water vapor. Output flow, pneumatic pipeline booster pump only 0.2-0.8Mpa compressed air. All O rings in the same series of pump, maintenance package damageable parts can be replaced by each other, thereby greatly reducing the maintenance cost, pneumatic pipe without the use of booster pump lubricant.
7, flexible application: booster pump booster pump from simple manual work to automatic work, booster pump is suitable for various applications, and facilitate customer compatible systems. In the air motor in the same series of most types of pumps are interchangeable

8, automatic pressure booster pump, booster pump work, work back and forth rapidly, with the output pressure of the pressure near the set value, the reciprocating speed of pump is reduced to a stop and keep the pressure. The energy consumption is small, no heat, no parts movement. When the pressure balance break booster pump automatic start work next a balance.


标签：

评论

发表评论

此博客中的热门博文

Why Ro booster pump in a water treatment system does not work?

Why Ro booster pump does not work?Let's find out the reason. Reverse Osmosis booster Pump is one of the key part of the RO water purification machine,we call it ro booster pump,It is a kind of booster pump be used in the reverse osmosis device, it has the function of self-priming and pressurization. Ro booster pump provide Ro membrane water pressure and water flow,to make Ro rembrane work. Ro membrane is another important component of the RO water purification machine.So Ro water purification machine can give us purifield water. Some times ro booster pump does not work,so the whole system is out of work,there are follow reasons cause the ro booster pump doesn't work: 1,Purifield water tank at a high level or the original water tank is at a low position. 2,Ro water pressure is higher than the protection switch Settings, the controller automatically switched on. 3,Ro booster pump suction pressure is lower than protection switch Settings, the controller automatically discon...
发表评论
阅读全文

How to exclude the interference from the frequency converter

These problems often occur when you work at regular work and debug the equipment： 1 . When the converter of the heat exchange station is opened , the pressure transmitter shall jump ; 2 . using frequency converter to control the water supply , the voltage transformer is used as a signal for collecting pressure , and the voltage transformer is interfered by the frequency converter ; 3 . When the frequency converter starts up the motor , the voltage change signal is unstable and the jitter is great ; 4 . The voltage transformer ( 4 – 20mA ) shall jump after the frequency converter is started , and the integrated thermal resistance ( 4 – 20mA ) nearby is not affected , and the signal line is not shielded . These phenomena are due to the interference of the frequency converter. Why does the inverter produce interference The inverter comprises a rectifying circuit and an inverter circuit , wherein the input AC power is converted into a DC voltage through a rectifying circuit and a wave loo...
发表评论
阅读全文

Difference between suction stroke and lift head of water pump

Pump self-priming capacity is also called maximum self suction height.It is the maximum height at which the water is pumped (the vertical distance between the pump and the the liquid surface to be pumped) without fill in water into the pump tunnel. General water level is lower than the location of the pump, you need to pump self-priming capacity.For example ,if we need to pump water from a river ,we will not plan pipe first,so we need a pump which has self-priming capacity. Or we need to pump some corrosive liquid,we can not fill water into the water pump tunnel. Some centrifugal water pumps do not have self-priming capacity,they need to fill in water at first time of using. The pump lift is the height that pump can lift water up.We usually expressed in H,the the unit is meter. The lift of the centrifugal pump is based on the center line of the impeller.The lift Consists of two parts,first is the vertical height from the center line of the pump impeller to the surface of the water s...
发表评论
阅读全文